YOUR PLUMBING CRASH COURSE: TIPS FOR BATHTUB INSTALLATION

Your Plumbing Crash Course: Tips for Bathtub Installation

Your Plumbing Crash Course: Tips for Bathtub Installation

Blog Article

Click Here!

This article following next pertaining to How to Install a Bathtub Yourself is amazingly informative. Read on and draw your own conclusions.


How to Install a Bathtub
Mounting a tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and often, tiling abilities. Changing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is conveniently easily accessible, the task can relocate quickly; if you need to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the job is within a house handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. Make certain you have certified yourself for the task and also are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed project, it is better to take into consideration using one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This article will certainly aid you mount a brand-new tub in your shower room if you have already bought a new bathtub and also do not need to transform the arrangement of your previous water system pipelines.
Your tools and product checklist should consist of the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted access that is commonly the instance.
    Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
    Prior to going on to fit the new taps, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, after that you will certainly require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipes.
    If you require to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet as well as the sink. Secure the tap in place with the maker provided backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.

    Setting up the Tub


    Making use of both wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
    The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the bath tub till the level reads level.
    To set up faucets, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression join; after that do the same for the other faucet.
    Activate the supply of water and check all joints and also brand-new pipework for leakages and tighten them if needed. Fill up the bathtub as well as likewise inspect the overflow electrical outlet and also the regular outlet for leakages.
    Finally, repair the bathroom paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub must wait until the bathtub has been utilized at the very least once as this will resolve it right into its last position.

    Preparing for the Installment


    Firstly, the supporting frame supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent strain on the bathtub.
    Fit the versatile faucet adapters to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the provided washing machines.
    Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its final position.

    Tiling Around the Tub


    In the location where the bathroom meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break a rigid seal, creating the water to permeate the wall surface in between the bath as well as the tiling, bring about complications with wetness and feasible leakages to the ceiling listed below.
    You can choose from a variety of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes as well as cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to allow for the activity experienced when the tub is in use. The sealant can crack relatively very early if you do not take into consideration this movement before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the market. It is a good idea to fit the floor tiles utilizing water-resistant or waterproof sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    I came across that post on How to Install a Bathtub when doing a lookup on the internet. Please set aside a second to share this post if you enjoyed it. Thanks a lot for your time. Come back soon.


    Emergency? We're here!

    Report this page